氣體增壓泵在使用一段時間后會出現增壓泵不工作或者上壓慢等故障。現在小編就將
氣體增壓泵常見的幾種故障通過表現來分析出現這種情況的原因和解決方法告訴大家。
After using the gas booster pump for a period of time, the booster pump will not work or the pressure will be slow. Now I will tell you the causes and solutions of several common faults of gas booster pump through performance analysis.
1.故障表現：當驅動氣體壓力不低于20psi時，驅動部分不工作或不循環。
1. Fault performance: when the driving gas pressure is not less than 20psi, the driving part does not work or does not circulate.
可能原因：供氣管路堵塞或供氣量不足；空氣循環閥堵塞；排放口結冰；消聲器堵塞。
Possible causes: the air supply pipeline is blocked or the air supply is insufficient; The air circulation valve is blocked; Icing at the discharge port; The muffler is blocked.
解決方法;檢查氣體供應管道和空氣調壓閥；拆卸空氣循環閥，并使用允許溶劑進行清洗；驅動氣體水含量較高，改用更好的干燥設備；將消聲器拆卸下來清洗。
resolvent; Check the gas supply pipeline and air pressure regulating valve; Disassemble the air circulation valve and clean it with the allowable solvent; The water content of the driving gas is high, and better drying equipment is used; Remove the muffler for cleaning.
2.故障表現：在負載情況下，驅動部分不工作，并在換向排氣口有連續氣體排出。
2. Fault performance: under load, the driving part does not work, and there is continuous gas discharge at the reversing exhaust port.
可能原因：換向針的彈簧破壞或不適合；換向針末端O型圈不適合或失去作用。
Possible causes: the spring of the reversing needle is damaged or unsuitable; The O-ring at the end of the reversing needle is not suitable or loses its function.
解決方法;置換彈簧；置換O型圈。
resolvent; Replacement spring; Replace the O-ring.
3.故障表現：驅動部分不工作；消聲器泄露空氣。
3. Fault performance: the driving part does not work; The muffler leaks air.
可能原因：驅動氣體流量不足；空氣循環閥芯的密封收縮或損壞。
Possible causes: insufficient driving gas flow; The seal of the air circulation valve core shrinks or is damaged.
解決方法;提高驅動氣體流量；首先檢測空氣循環閥芯的密封，如果損壞，更換并組裝重新測試；如果沒有損壞，檢查驅動部分密封。
resolvent; Increase the flow rate of driving gas; First, check the seal of the air circulation valve core. If it is damaged, replace it, assemble it and retest it; If there is no damage, check the drive part seal.
4.故障表現：驅動部分工作，但氣體沒有增壓。
4. Fault performance: the driving part works, but the gas is not pressurized.
可能原因：氣體壓縮部分的單向閥密封或高壓部。
Possible cause: check valve seal or high pressure part of gas compression part.
This is how to analyze the common faults of booster pump through performance. If you have any doubts about this, please come to our website at any time http://www.madaboutmermaids.com For consultation, customer service personnel will serve you wholeheartedly!
