網站公告:

新聞中心

濟南精拓流體設備有限公司

電話:0531-69951198

郵箱:jingtuolt@163.com

傳真:0531-69951198

地址:濟南市歷城區西周南路9號

網址:http://www.madaboutmermaids.com

常見問題

當前位置:首頁 - 新聞中心 - 常見問題 - 氣體增壓泵的使用六點注意

氣體增壓泵的使用六點注意事項

發布時間:2022-10-05 17:36:32   發布人:http://www.madaboutmermaids.com
氣體增壓泵是給氣體增壓的一種,其原理是利用低壓氣體推動大活塞來帶動高壓增壓缸的小活塞,通過計算大小活塞的面積比來得到氣體增壓泵的增壓比。下面來講講氣體增壓泵的使用六點注意事項,具體如下:
The gas booster pump is a kind of gas booster pump. Its principle is to use low pressure gas to drive the large piston to drive the small piston of the high pressure booster cylinder. The pressurization ratio of the gas booster pump is obtained by calculating the area ratio of the large and small pistons. Here are six precautions for the use of the gas booster pump, as follows:
1.使用方要準備好被增壓的氣體和管路,驅動氣體和管路,高壓氣體的出口管路,按增壓泵出廠時所帶的說明先固定好增壓泵,按照增壓泵的各個進出口接頭尺寸,連接好管路;檢查是否耐壓足夠,接頭是否有泄露等,檢查完好后就可以進行增壓測試了。
1. The user shall prepare the pressurized gas and pipeline, driving gas and pipeline, and outlet pipeline of high-pressure gas, fix the booster pump according to the instructions of the booster pump when it leaves the factory, and connect the pipeline according to the size of each inlet and outlet connector of the booster pump; Check whether the pressure resistance is sufficient and whether the connector has leakage. After the check is complete, the pressurization test can be carried out.
2.氣源方面:氣體增壓泵的驅動氣源壓力范圍一般是在1.8-8bar,不建議它的驅動氣源超過10bar,如果驅動氣源過高,那么很大程度上會對泵體造成損傷,更有甚者會對操作人員造成傷害。
2. Air source: The driving air source pressure range of the gas booster pump is generally 1.8-8bar. It is not recommended that its driving air source exceed 10bar. If the driving air source is too high, the pump body will be damaged to a large extent, and even the operators will be injured.
3.選型方面:客戶要根據自身需求的壓力選擇對應的增壓比,按照客戶自己的壓力需求,突出氣源壓力、進氣壓力、輸出壓力需求、流量是多少,這樣技術人員才能更準確的幫您選型。
3. Model selection: The customer should select the corresponding boost ratio according to the pressure of their own needs, and highlight the air source pressure, intake pressure, output pressure demand and flow according to their own pressure needs, so that the technicians can help you select the model more accurately.
氣體增壓泵
4.對現場使用環境方面:現場使用環境一定要干凈,不能有太大的粉塵顆粒,驅動氣源及被增壓介質水分不要含量太多,否則會大大降低泵的使用的壽命。
4. For the on-site use environment: the on-site use environment must be clean and free of too large dust particles. The driving air source and pressurized medium should not contain too much moisture, otherwise the service life of the pump will be greatly reduced.
5.對管路的要求:客戶現場使用的時候一定要檢測高壓輸出管道的密封嚴實性,采用的管道、閥門、壓力表一定要大于氣體增壓泵輸出的額定壓力,大限度的保證人員的操作安全。
5. Requirements for pipelines: When using on site, the customer must check the tightness of the high-pressure output pipeline. The pipes, valves and pressure gauges used must be greater than the rated pressure output by the gas booster pump, so as to ensure the operation safety of personnel to a large extent.
6.對壓力容器的要求:各部分承壓件,特別是壓力容器,要具有壓力安全容器廠家生產的壓力安全容器檢查報告。
6. Requirements for pressure vessels: all pressure parts, especially pressure vessels, shall have inspection reports of pressure safety vessels produced by pressure safety vessel manufacturers.
此外氣體增壓泵的壽命是由動作的頻率決定。因此如果設備需要長時間運轉,請在工況中說明,技術人員會討論決定泵的類型,這樣會大大增壓增壓設備的使用壽命期限。更多相關內容就來我們網站http://www.madaboutmermaids.com咨詢!
In addition, the life of the gas booster pump is determined by the frequency of action. Therefore, if the equipment needs to operate for a long time, please explain in the working conditions, and technicians will discuss and decide the type of pump, which will greatly increase the service life of the supercharging equipment. More relevant content will come to our website http://www.madaboutmermaids.com consulting service
新聞推薦:
氣體增壓泵要保持清潔及系統安全使用 2022-10-19
氣液增壓泵是如何進行工作的? 2022-10-12
氣體增壓泵的使用六點注意事項 2022-10-05
采購及使用氣液增壓設備需注意幾點 2022-09-25
氣液增壓泵的原理特點以及應用 2022-09-19
氣體增壓泵使用之前知道六要點 2022-09-17
氣體增壓泵如何工作以及如何維護 2022-09-15
氣體增壓泵和氣液增壓缸的工作原理不同 2022-09-05
怎么判斷各類型的增壓泵好與壞? 2022-08-26
通過表現來分析增壓泵常見幾種故障 2022-08-24

13188935873

qq

欧洲精品无码一区二区三区在线播放,欧美性爱动图,欧美人与动交片免費播放,欧美成在线精品视频